fischer Bolt Anchor FBN II

fischer bolt anchor fbn ii

The FBN II is fischer's cost-efficient bolt anchor for non-cracked concrete. It is made in zinc plated, hot-dip galvanised and stainless steel, and the sizes below are the ones Avlock supplies.

See sizes and specs 52 sizes

  • The standard anchorage depth gives the highest load capacity, so fewer fixing points and smaller anchor plates are needed.
  • A long thread balances out tolerances and makes stand-off installation possible.
  • Two anchorage depths, standard and reduced, give flexibility on site.
  • The head marking shows at a glance that the anchor has been set correctly.
  • Covered by a European Technical Assessment (ETA).

Supplied by Avlock International to industrial and projects customers, with local technical support.

Talk to an expert WhatsApp us

How the fixing works

The FBN II is a torque-controlled expansion anchor. When the nut is tightened, the cone bolt is pulled into the expansion clip, which presses against the wall of the drilled hole.

Read moreShow less

It suits pre-positioned and push-through installation. The long thread also allows stand-off installation under certain conditions.

Where it is used

  • Steel constructions
  • Guard rails
  • Consoles
  • Ladders
  • Machines
  • Gates
  • Façades
  • Cable trays

Sizes and article numbers

Bolt anchor FBN II: sizes and article numbers
Sizefischer art. no.ThreadMax. fixture thicknessFinish
FBN II 6/10505527M610 mmZinc plated
FBN II 6/30505528M630 mmZinc plated
FBN II 8/10507575M810 mmHot-dip galvanised
FBN II 8/10507555M810 mmStainless steel A4 (R)
FBN II 8/1040664M810 mmZinc plated
FBN II 8/30507556M830 mmStainless steel A4 (R)
FBN II 8/3040700M830 mmZinc plated
FBN II 8/30560944M830 mmZinc plated
FBN II 8/5 K508012M85 mmHot-dip galvanised
FBN II 8/5 K508007M85 mmStainless steel A4 (R)
FBN II 8/5 K40806M85 mmZinc plated
FBN II 10/10507579M1010 mmHot-dip galvanised
FBN II 10/10507558M1010 mmStainless steel A4 (R)
FBN II 10/10560924M1010 mmZinc plated
FBN II 10/2040851M1020 mmZinc plated
FBN II 10/20560925M1020 mmZinc plated
FBN II 10/30507580M1030 mmHot-dip galvanised
FBN II 10/30507560M1030 mmStainless steel A4 (R)
FBN II 10/3040854M1030 mmZinc plated
FBN II 10/30560926M1030 mmZinc plated
FBN II 10/5040855M1050 mmZinc plated
FBN II 10/14040944M10140 mmZinc plated
FBN II 10/5 K508013M105 mmHot-dip galvanised
FBN II 10/5 K508010M105 mmStainless steel A4 (R)
FBN II 10/5 K40946M105 mmZinc plated
FBN II 10/5 K560922M105 mmZinc plated
FBN II 12/10507589M1210 mmHot-dip galvanised
FBN II 12/10507563M1210 mmStainless steel A4 (R)
FBN II 12/1040950M1210 mmZinc plated
FBN II 12/20507564M1220 mmStainless steel A4 (R)
FBN II 12/2044558M1220 mmZinc plated
FBN II 12/30507591M1230 mmHot-dip galvanised
FBN II 12/30507565M1230 mmStainless steel A4 (R)
FBN II 12/3045263M1230 mmZinc plated
FBN II 12/50507592M1250 mmHot-dip galvanised
FBN II 12/50560936M1250 mmZinc plated
FBN II 12/10045266M12100 mmZinc plated
FBN II 12/5 K508014M125 mmHot-dip galvanised
FBN II 12/5 K508011M125 mmStainless steel A4 (R)
FBN II 12/5 K560930M125 mmZinc plated
FBN II 16/25507598M1625 mmHot-dip galvanised
FBN II 16/25507569M1625 mmStainless steel A4 (R)
FBN II 16/2545564M1625 mmZinc plated
FBN II 16/8045566M1680 mmZinc plated
FBN II 16/15 K507597M1615 mmHot-dip galvanised
FBN II 16/15 K508745M1615 mmStainless steel A4 (R)
FBN II 16/15 K45571M1615 mmZinc plated
FBN II 20/30508015M2030 mmHot-dip galvanised
FBN II 20/30507571M2030 mmStainless steel A4 (R)
FBN II 20/3045573M2030 mmZinc plated
FBN II 20/10 K543973M2010 mmHot-dip galvanised
FBN II 20/10 K45577M2010 mmZinc plated

In a size such as 10/30, the first number is the thread size (M10) and the second is the maximum thickness of the fixture in mm. K marks the short version. The article numbers are fischer's. Some sizes have two article numbers because fischer has issued a new number for the same anchor.

Pack sizes and trade quantities on request. Need a size or product that isn't listed? Ask us. fischer's full range is also on fischer's website. Not sure which size you need? Tell us the base material and the fixture thickness, and we will help you choose.

Ask about this product WhatsApp us

Suitable base materials

Approved for

  • Concrete C20/25 to C50/60, non-cracked

Also suitable for

  • Concrete C12/15
  • Natural stone with a dense structure

For approval details and the loads each combination can take, see the fischer load table.

Installation and safety notes
  • Approved for non-cracked concrete. For cracked concrete, see the FAZ II range.
  • The short (K) versions suit pre-positioned and push-through installation.
  • Stand-off installation is possible under certain conditions. Check fischer's installation instructions.
  • Choose the finish for the conditions: the zinc plated version is for dry indoor use, the hot-dip galvanised and stainless steel versions for damp or outdoor use. The approval documents give the working life for each.
  • For series installation, fischer recommends the FABS setting tool.
  • Always check fischer's technical documents (ETA and load data) for your base material before you specify or install.